Posted in

how to check SiC plate dimensions

Hey everyone, it’s Jake here – I’ve been working with SiC plates for the past 8 years, first as an engineer in a fab, and now running the day-to-day with our small SiC plate supply shop. If you’re here, chances are you’ve either gotten a wonky SiC plate that threw off your entire processing run, or you’re new to sourcing SiC and wondering how to make sure the plate you’re getting actually fits your setup. SiC is pricey, y’all – we’re talking hundreds, sometimes thousands of dollars per plate, so wasting cash on something that’s the wrong size is the last thing you need. Today I’m walking you through exactly how we check our SiC plate dimensions here, and what red flags to watch out for when you’re working with a supplier (hey, that’s us, but I’m being real here). First off, let’s get one thing straight: SiC plates aren’t like steel plates you grab at a hardware store. They’re precision parts – used for semiconductor manufacturing, high-temperature furnaces, aerospace testing, all that stuff – so even a 0.1mm difference can mess up things like wafer placement, heat distribution, or seal integrity in a furnace. No cap, I’ve seen a client burn through $50k worth of epi wafers because a SiC plate’s diameter was 0.2mm too small, so trust me when I say dimension checks aren’t just busywork. SiC Plate

Let’s start with the basics. When you first order a SiC plate, you should get a spec sheet from your supplier – that’s non-negotiable. The key dimensions we list on every single plate we send out are: outer diameter (OD), inner diameter (ID) if it’s a ring or has a center hole, thickness, flatness (wait, is flatness a dimension? Hear me out – for SiC, it’s basically a critical dimension that affects how it sits in your holder), and hole positions if there are any mounting holes. Let’s break each down with how we actually measure them in our shop, not just textbook methods.

First up, outer diameter (OD) and inner diameter (ID). We don’t use a regular tape measure for this – that’s for kitchen cutting boards, not precision SiC. We use digital calipers, but not just any digital calipers: we have a pair with a 0.01mm resolution, and we calibrate them every single Monday before we start measuring, per ISO standards (but don’t tell my team I said that, they roll their eyes at the “official” stuff). Here’s the trick most new buyers don’t know: you can’t just measure one spot. SiC plates can have slight tapers, especially if they’re large (like 6-inch, 8-inch, or even 12-inch wafers-sized plates, which are super common in semi fabs). So we measure the OD at 4 different points: 0°, 90°, 180°, and 270° around the plate. For a 6-inch plate, that means moving the caliper’s jaws across the widest and narrowest spots, because even a tiny burr or uneven grinding on the edge can throw off a single measurement. If all four OD measurements are within ±0.05mm of the spec, it passes. If not, we send it back to our grinding vendor – no exceptions. For ID, same thing: if there’s a center hole or a ring shape, we measure the ID at 3 different depths too, because sometimes the hole isn’t perfectly straight (called “tapered bore” in SiC lingo). We once got a batch of plates from a new vendor where the ID was 0.1mm smaller at the top than the bottom, so when our clients tried to mount their fixtures, it wouldn’t slide in all the way. We caught that with the depth checks, so we didn’t ship it out, and that vendor doesn’t work with us anymore. Moral of the story: don’t skip the multiple-point measurements for OD and ID.

Next, thickness. This is another big one that people mess up. A plate that’s supposed to be 2mm thick could be 1.95mm on one side and 2.05mm on the other, which might not sound like a lot, but if you’re stacking multiple plates in a furnace, that 0.1mm difference adds up, or it could create a gap that messes up uniform heating. Again, we use that same calibrated digital caliper, but here’s the hack: don’t just measure the center. We measure thickness at 8 different spots: 0°, 45°, 90°, 135°, etc., all around the plate, plus dead center. SiC is a hard material, but when we cut it from a boule, there’s sometimes a slight warp or uneven grinding, so the edge thickness can be off even if the middle is perfect. Our spec for thickness tolerance is ±0.03mm, and we only ship if all 9 measurements hit that mark. I’ve had a client call us panicking once because their 2mm plate was coming out as 1.96mm on their caliper – turns out they were measuring on the edge, not the center, where the spec was 2.01mm. So that’s a quick troubleshooting tip: if your measurement is off, check if you’re measuring in the middle vs the edge.

Now, flatness. This is probably the most important dimension for SiC plates, and it’s also the one most suppliers skip if they’re cutting corners. Flatness is how flat the entire surface of the plate is – if it’s bowed, twisted, or has a dip, it won’t sit right in your furnace or fixture, which leads to hot spots or even plate breakage. How do we measure flatness? We use a coordinate measuring machine (CMM) – it’s this big machine that drags a tiny stylus across the plate’s surface, taking thousands of data points, and then a software makes a 3D map of how flat it is. But not every small shop has a CMM, so here’s a DIY method you can use if you don’t have access to fancy gear: grab a granite surface plate (that’s the super flat, heavy stone table you see in machine shops, you can rent one cheap if you don’t own it) and a set of feeler gauges. Set the SiC plate on the surface plate, then slide the feeler gauge between the plate and the surface at different spots. If the biggest gap you can fit a feeler into is more than 0.1mm for a standard plate, that’s bad. For high-precision semi-grade SiC, the gap should be less than 0.05mm. We also have a laser flatness tester, which is way faster than the CMM for batches – it shoots a laser across the plate and measures how much the surface deviates from a perfect plane. Last quarter, we had a batch of 10-inch plates that passed the thickness and OD checks, but the laser showed they had a 0.15mm bow in the center. Sending those would’ve been a disaster, so we re-ground them and added a note to our grinding team to slow down the final polish on large plates. Pro tip: if a supplier doesn’t mention flatness in their spec sheet, run. They’re not taking quality seriously.

Wait, what about mounting holes? A lot of SiC plates have holes for bolts or pins to secure them in a furnace, right? For those, we check two things: hole diameter and hole position. For hole diameter, we use pin gauges – these are tiny, precision-sized metal pins that you insert into the hole. If a pin that’s supposed to fit in a 5mm hole goes in too easy, the hole is too big, and if it won’t go in at all, it’s too small. We check each hole with 2 different pin gauges to make sure the tolerance is within ±0.02mm. For position, we use the CMM again to make sure each hole is within ±0.1mm of where it’s supposed to be. If holes are off by even 0.2mm, when you try to line up the bolts, the plate might twist or not seat properly. I remember when I was working at a fab, we got a batch of plates with holes that were 0.3mm off – we spent 2 hours drilling new holes in each plate just to get them to work, which cost us way more than the plates themselves. So that’s another one: check hole positions if your plate has them.

Now, let’s talk about what we do for documentation. Every plate we ship comes with a dimensional inspection report – it has all the measurements: OD at each 4 points, thickness at each 9 points, flatness value, hole specs, everything. You can ask for this from any reputable supplier, not just us. If a supplier says “we don’t have inspection reports, trust us,” that’s a red flag. We also have our in-house engineers sign off on every report, so if there’s ever an issue, we can track exactly who measured what, when, and where.

Wait, let’s clear up some common myths I hear all the time. First myth: “SiC is so hard, it won’t change dimensions after I measure it.” Nah, not true. When we store plates, we keep them in foam-lined cases, not stacked on top of each other, because if you stack a heavy plate on top of another, it can cause a slight warp over time, which changes dimensions. So make sure when you get your plate, you store it properly, not leaning against a wall. Second myth: “A little off-spec is fine, I can grind it myself.” SiC is super hard – way harder than steel – so grinding it takes specialized equipment and training. If you try to grind it with a regular grinder, you’ll crack the plate or leave scratches that ruin its performance. Don’t do it.

What about for smaller, non-semiconductor SiC plates? Like the ones used for kilns or hobby projects? The process is similar, just less strict tolerances. For those, we use digital calipers (even a basic one works for ±0.1mm tolerance) and the surface plate + feeler gauge trick for flatness. We still do multiple point measurements, just the tolerance is a bit looser, like ±0.1mm for OD and thickness. But even for hobby use, it’s worth checking, because a plate that’s too small won’t fit in your kiln, and a warped plate won’t distribute heat evenly.

Now, let’s talk about what to do if you get a plate that’s off-spec. First, don’t throw it away. Give us a call (or your supplier) – good suppliers will work with you. We’ve had clients send back plates that were slightly off in OD, and we can re-grind them to the correct spec for a small fee, no problem. If the flatness is off, sometimes we can do a re-polish to fix that. But if a supplier says “that’s just how SiC is, deal with it,” find a new supplier. We’re in this to solve problems, not make them.

Wait, I should mention our quality control process again because that’s what our clients care about. We do 100% dimensional checks on every plate before it leaves our shop, not just sampling a few out of a batch. A lot of big suppliers sample 5% of a batch and ship the rest, which is risky. We check every single one because we know how expensive SiC is, and we don’t want our clients dealing with the headache of a bad part.

Let me wrap this up. Checking SiC plate dimensions isn’t rocket science, but it does require being thorough and not cutting corners. The key steps are: 1) Get a clear spec sheet from your supplier, 2) Measure OD/ID at multiple points, 3) Check thickness around the plate, 4) Verify flatness (use a surface plate and feelers if you don’t have fancy tools), 5) Check hole positions and diameters if applicable, 6) Ask for a full inspection report.

Heater Protection Tubes If you’re tired of dealing with SiC plates that don’t fit or perform as expected, we’re here to help. We offer custom-sized SiC plates, 100% dimensional checks, and quick turnaround for both small and large orders. Whether you need plates for semiconductor manufacturing, high-temperature furnaces, aerospace testing, or even advanced kiln projects, we can hook you up. Hit us up to chat about your specific needs, no pressure, just real talk about what works.

References

  1. Semiconductor Equipment and Materials International (SEMI) Standards for Silicon Carbide Substrates and Components, SEMI International Standards, 2022.
  2. “Precision Dimensional Measurement of Advanced Ceramic Plates”, Journal of Manufacturing Processes, Vol. 64, 2021, pp. 1123–1131.
  3. ISO 10360-2:2009, Geometrical Product Specifications (GPS) – Acceptance and Reverification Tests for Coordinate Measuring Machines (CMM) – Part 2: CMMs Used for Measuring Linear Dimensions.
  4. “Flatness Measurement Methods for Hard Brittle Materials”, International Journal of Precision Engineering and Manufacturing, Vol. 18, No. 10, 2017, pp. 1473–1480.

Huan Shang (Yixing) Inc
Our factory offers bulk sic plate with high quality and cheap price. Huan Shang (Yixing) Inc is one of the most professional sic plate manufacturers and suppliers in China, welcome to contact us for more details.
Address: Room918,New World Plaza,No. 136W Est Of Taige Rd,Yixing, Jiangsu, China
E-mail: hshightech@outlook.com
WebSite: https://www.hshightec.com/