Posted in

How to make a concrete bar top?

If you’ve ever walked into a bar and lingered over a smooth, weighty concrete bar top that looked like it could hold a thousand drinks without so much as a micro-scratch, you know there’s a quiet craft to making them. As someone who’s spent the last eight years supplying custom concrete bar tops to restaurants, breweries, and home bar owners across the country, I’ve seen way too many folks try to DIY one and end up with a cracked, lopsided mess that doesn’t live up to the vibe they were going for. Making a concrete bar top isn’t just mixing cement and pouring it, though—there’s a science to the mix design, a rhythm to the pouring, and small, easy mistakes that can sink an otherwise great project. Over the years, I’ve refined the process into something consistent, durable, and beautiful, and I’m breaking it all down here for anyone looking to tackle this, whether you’re a homeowner upgrading your man cave or a bar owner ordering your first commercial-grade top. Bar Top

First, let’s start with the foundation—your mix. This is the part that separates a bar top that lasts 10 years from one that crumbles in two. A lot of beginners grab a standard bag of all-purpose concrete mix from a hardware store, and while that works for patios, it’s way too porous and weak for something that will take constant impact, spills, and the weight of bar equipment like tap handles or bottle racks. For bar tops, we use a custom mix designed specifically for thin, durable pours (most bar tops are only 1.5 to 2 inches thick, after all). Here’s the breakdown we rely on at the shop: 1 part portland cement, 2 parts fine silica sand (not coarse builder’s sand—fine gives a smoother finish), 1 part lightweight aggregate (we use expanded shale, which cuts down on weight without sacrificing strength), and a superplasticizer admixture. The superplasticizer is non-negotiable here; it’s a chemical that lets the mix flow easily without adding extra water (too much water makes concrete weak and prone to cracking). For every 80-pound bag of portland cement, we add about 12 ounces of liquid superplasticizer. We also add a color pigment—iron oxide, usually, for warm grays, blacks, or tans—that’s specific to concrete, not paint pigment, because paint will float out and leave a splotchy finish. Pro tip: Mix small batches (no more than 50 pounds at a time) in a wheelbarrow with a hoe, not a power mixer—power mixers can whip too much air into the mix, leading to air bubbles that show up as pockmarks on the finished surface. And don’t overwork the mix once all ingredients are combined; just stir until it’s the consistency of thick cake batter, and use it within 45 minutes, because concrete sets fast.

Next, the mold. This is where you shape your bar top, and if you want a straight, even edge (no lumpy, uneven sides), you need to build it right. We build molds from medium-density fiberboard (MDF) because it’s cheap, smooth, and doesn’t warp when exposed to concrete moisture. You can also use plywood, but MDF gives a cleaner edge. First, measure your base: standard bar tops are 42 inches high, with a top that extends 8 to 12 inches beyond the base for elbow room. For the mold, cut your MDF pieces to the exact dimensions of your finished top, adding a 1-inch lip all around the perimeter to hold the concrete in. If you want a curved edge (a popular look for modern bars), you can bend MDF—just score the back of the MDF every half inch with a utility knife, then wet it a little and bend it to your desired curve, clamping it in place while it dries. Before pouring, coat every surface of the mold with a concrete release agent—we use a paste of mineral oil and melted paraffin wax, which is cheaper than commercial release sprays and works just as well. If you skip this, your concrete will stick to the MDF and you’ll tear the edges when you try to remove it, which is a nightmare. Also, reinforce the mold from the outside with 2x4s and clamps: concrete is heavy—each cubic foot weighs about 150 pounds, so a 8-foot-long bar top will weigh well over 100 pounds. If the mold isn’t braced tightly, it will bulge or break during pouring. We also add a rebar grid for extra strength in commercial projects—use 4-gauge welded wire mesh cut to the size of your top, and prop it up 1 inch above the mold bottom with small concrete spacers so it’s centered in the pour. For DIY projects, you can skip rebar and just use a layer of fiberglass mesh, which is lighter and works for residential tops.

Now, the pouring process—this is where most people go wrong, especially if they’re trying to pour a large top. Start by pouring a 1/2-inch base layer first, then use a trowel to gently work it into the corners and around the rebar or mesh, making sure there are no air pockets. Air bubbles are the enemy here; they’ll leave small holes in the finished surface, so take a spud bar (a long, thin metal rod) and poke the concrete every 2 to 3 inches all over the top, then tap the sides of the mold with a rubber mallet to release any trapped bubbles. Once the base is evenly spread, pour the rest of the mix to fill the mold to the top. For the final layer, we smooth it with a magnesium float—this tool is key because it compacts the top of the concrete without pulling excess water to the surface (excess water causes a weak, dusty top). Work the float in a circular motion, applying firm pressure, until the surface is flat and you can see a thin sheen of water—stop right there. If you over-float, you’ll grind the fine particles to the top and leave a surface that scratches easily. If you under-float, the top will be rough and prone to staining.

After pouring, the curing process is the most important step for durability, and it’s the one most beginners skip. Concrete needs time to hydrate—this is what makes it strong, not just drying. If you let a new bar top dry out too fast, it will crack and turn chalky. We cure our tops for 7 days, which is the industry standard for commercial use. Here’s how: After the float, cover the top with a plastic sheet (tarp, sheeting, whatever you have) immediately to trap moisture, and keep it covered for at least 3 days. Then, mist the top with water twice a day for the next 4 days—don’t let it dry out at all. In dry climates, you can also use a curing compound spray, but misting is cheaper and works just as well if you’re consistent. Once the curing is done, you can remove the mold. Do this after 7 days, not earlier—even if the concrete feels hard on top, it’s still curing. Pop the clamps and take off the MDF, and you’ll see your rough, matte concrete bar top. Now it’s time to finish it.

Finishing is where you get to customize the look, and it’s also the part that protects your bar top from spills, scratches, and daily wear. We use a two-part epoxy sealer for all our bar tops because it’s durable, heat-resistant (it can handle hot plates or mugs straight from the microwave), and gives a glossy or matte finish. First, lightly sand the concrete surface with 120-grit sandpaper to remove any rough spots, then wipe it down with a tack cloth to get rid of all dust. Mix the epoxy according to the manufacturer’s instructions (always follow the exact ratios, or it won’t cure properly), and pour it evenly over the top. Use a squeegee to spread it thin, then go over it with a foam roller to get rid of bubbles. For edges, you can use a small brush to work the epoxy into corners where the roller can’t reach. Let the first coat cure for 24 hours, then sand it lightly with 220-grit sandpaper, wipe again, and apply a second coat. Two coats give enough protection to last for years. If you want a different look, you can add a stain or acid etch before sealing—acid etches give a variegated, natural look, while concrete stains come in a range of colors to match your space. Just test any stain on a small, hidden area first to make sure you like the color, and seal it immediately after staining to lock it in.

Over the years, I’ve picked up a few tricks that make the difference between a good bar top and a great one. For example, if you’re making a bar top that will have a sink or a cutout for a tap system, do that cutout before pouring, not after—carving concrete once it’s cured is messy and can cause cracks. For commercial bars, we also add a 4-inch backsplash along the wall edge, which we build into the mold so it’s seamless, no seams where the top meets the wall. Another thing: if you’re making a custom size, don’t try to pour too big a top in one go—anything over 8 feet long should be poured in two sections, with a metal reinforcement strip in the middle, to prevent cracking as it cures. I’ve seen way too many bar owners order a 12-foot top that cracked down the middle because they tried to pour it in one piece, and it’s a hassle to fix.

Now, if all of this sounds like a lot—because, let’s be real, it is, especially if you don’t have experience working with concrete—we’re here to help. At our shop, we supply custom concrete bar tops tailored to every need, whether it’s a residential home bar that fits in a small basement or a commercial bar for a 100-seat restaurant. Each top we make follows the exact mix and curing process I’ve outlined, so you know it’s going to be strong, durable, and look exactly how you want it. We work with your measurements, can add custom edges, colors, or cutouts for sinks and tap systems, and we ship nationwide, so you don’t have to worry about picking it up or installing it. If you’re planning a project—whether you’re a first-time homeowner or a bar owner looking to upgrade your space—we’d love to walk you through the process, answer any questions, and help you design a bar top that works for you.

Shower Base Tray References

  1. "Concrete Countertop Mix Design Guidelines" – American Concrete Institute, 2018.
  2. "Curing Requirements for Structural Concrete" – Portland Cement Association, 2020.
  3. "Epoxy Sealing for Concrete Surfaces" – National Ready Mixed Concrete Association, 2019.
  4. "Formwork for Concrete Countertops" – Concrete Decor Magazine, 2021.

Xiamen HRST Stone Co., Ltd.
Xiamen HRST Stone Co., Ltd. is one of the most professional bar top manufacturers and suppliers in China, specialized in providing high quality stone products with competitive price. We warmly welcome you to buy or wholesale the best bar top for sale here from our factory. Also, custom service is available.
Address: Xijing District, Shuitou Town, Quanzhou City, Fujian Province, China
E-mail: jack@hrststone.com
WebSite: https://www.hrststone.com/